|FIXED LINE ADSL - TECHNICAL DATA|
TerminologyThe term broadband simply means a broad band of frequencies has been used. It is a radio term and normally means that multiple frequency carriers are used to carry one signal. It describes the way ADSL (Asymmetric Digital Subscriber Line) services work so has become a term to describe a fast internet connection. The term is then being rather confusingly used to describe fibre connections which are not broadband at all, but use a single frequency laser.
FrequencyNormal telephone service is an analogue of sound waves. It carries sound using electrical signals that work in the same way as they do though air. In terms of frequency this means that telephone calls use very low frequency signals on the telephone line. The line itself can carry signals at a much higher frequency. The limiting factor is the quality and length of the cable used. Normal telephone lines are a copper pair (two insulated copper conductors twisted around each other) that can go for several miles from the local telephone exchange to your premises. ADSL makes use of the rest of the capabilities of the cable. It carries data using a wide range of frequencies much higher than that used for telephone calls. The fact that it uses this broad band of frequencies is why it is called broadband.
Adapting to the line characteristicsOne of the key features of ADSL is that it can adapt to work on a variety of line quality and lengths. A long line cannot carry the same range of signals as a short line. Lines can also suffer from specific interference which only affects some frequency bands. So the line will sync to start with. Syncing means that each end sends a range of different signals and the other end reports back what it can hear. This allows the modems at both ends to work out what the line can handle, and what frequencies work. For each of hundreds of different frequency bands the modems agree how many bits of data can be carried at a time in that band. What this means is that the line can work at different speeds depending on the length and quality of the line. If, over time, the line characteristics change the line will have to re-sync which usually means a short outage in service.
MarginsRe-syncs are a pain as they normally mean a broadband service stops for several seconds to re-establish the line characteristics. This is not generally a good thing. To help avoid re-syncs the initial measurements of the line characteristics are adjusted to allow a margin. This means not all of the line's capabilities are used. If the line degrades over time, and that degradation is within this margin, then no re-sync is needed. Some lines are very stable, having the same characteristics all of the time. These lines need very low margins. However some lines vary a lot, and this can be over a daily cycle depending on temperature or weather conditions which affect the performance of the line and levels of interference affecting the line. Such lines need higher margins. There is an automatic system to establish that a line is re-syncing a lot and adjust the margin to be higher in future. This is called Dynamic Line Management (DLM) and runs all of the time. It can take a few days for a new line to get the right margins for stable operation when first install, but in practice it is rarely more than the first few hours.
The margin on the line sync helps accommodate general changes in the performance of a line over time. However there can be interference that is more like "pops and clicks". Impulse interference that causes corruption of data. This causes packets to be lost and resent and so has the effect of making the overall performance of the line slower. To accommodate this type of interference a system of error correction is used. This means extra parity data is sent, and if data is corrupted then this can be identified and corrected. It uses a small amount of the available bandwidth to provide this extra parity data but makes the line much less prone to errors. At the same time the data is interleaved. This means overlapping each block of data with the next and is the same trick used on CDs to make them resist the effects of scratches on the surface. The effect is higher latency (the time taken for data to get through the ADSL).
ADSL has been defined for use along side normal phone service as well as along side ISDN. The different frequency for ISDN means it is a different standard. In the UK we use ADSL over POTS (Plain Ordinary Telephone Service) following ITU G.922.1 Annex A which allows in theory up to 12Mb/s downstream and 1.3Mb/s upstream. However BT offer only 8.128Mb/s downstream and 832Kb/s upstream maximum using ADSL1.
A new standard for ADSL called ADSL2+ provides extended bandwidth. This follows ITU G.992.5 and provides up to 24Mb/s downstream and 1Mb/s upstream. A variation of the ADSL2+ specification called Annex M allows up to 24Mb/s downstream and up to 3.5Mb/s upstream. In the UK we cannot achieve the full 3.5Mb/s upstream as there is a frequency plan that must be followed on all phone lines to avoid interference. This limits the Annex M uplink. Whilst Annex M is not yet available in the UK we expect it to allow around 2Mb/s uplink.
Upgrade to 21CNExisting lines on 20CN will be upgraded to 21CN and so allow ADSL2+. This is part of an ongoing programme. The upgrade may be some months after ADSL2+ is available on the exchange, and so customers can pay a small fee to upgrade sooner if the exchange is ready. Upgrades as part of our upgrade programme are free of charge and we email you several weeks in advance with details. When we upgrade we initially keep your line on ADSL1 on the new 21CN kit, and then change to ADSL2+ a few days later.
Beyond the exchangeThe ADSL/broadband bit connects between your premises and the local telephone exchange, at which point the line is split between voice (for telephone calls) and ADSL. The local exchange is connected via fibre to one of 20 main interconnect points where a large fibre back-haul network connects back via gigabit fibre links to our rack in a data centre in Docklands. We are then connected by fibre so that we can communicate directly with hundreds of UK based ISPs as well as international (transit) links to the rest of the world.